Tuesday 30 June 2015

Fault code Xerox DC 240/242/250/252/260/WC 7655/7665/7675/7755/7765/7775


Fault Code:
Description / Notes:

002-770
The Hard Drive (HDD) is over capacity

003-xxx codes
Generally: Communication Errors between boards in the machine

005-xxx codes
Generally: Document Feeder problems

005-121 thru 005-158
Document Jams

005-194 thru 005-199
Document size mismatch problems

005-275/280
Document Feeder communication errors

005-281 thru 005-283
Document Tray lift problems

005-284
Document APS (Automatic Paper Sensors) failure (there are 3 sensors which detect various paper widths on the Document Feeder)

005-285
Document Nudger up failure

005-286
Document feed-out sensor failure

005-303
Document Tray Interlock is open

005-304
Document Platen Interlock opened during a job

005-305
Document Top Cover Interlock opened during a job

005-306
Document Tray Interlock opened during a job

005-308/309
Document Left Cover is open or opened during a job

005-906 thru 005-918
Document is still detected in feeder after power-on or after closing one of the document door interlocks

010-xxx codes
Generally: Fuser faults

010-311
Open Fuser Thermistor was detected (white connector)

010-319 *
Fuser Heat Control problem *NOTE: This code must be cleared from Diagnostic Mode… details below.

010-320 **
Fuser Overheat problem… (can be reported by any of the 3 thermistors in the fuser) ** NOTE: This code must be cleared from Diagnostic Mode… details below.

010-322 thru 010-323
Fuser Thermistor open circuit detected (NCCenter Sensor or Rear Thermistor)

010-324***
Fuser NVM (Memory) failure *** NOTE: This code must be cleared from Diagnostic Mode… details below.

010-326 thru 010-327
Fuser Heat Control problems

010-330
Fuser Motor failure

010-420
Fuser Module nearing end of life... NOTE: Read below for fuser count reset info.

010-421
Fuser Module "End of Life"… NOTE: If the fuser is still good, you can replace the Fuser Reset Fuse (on top of the fuser) and possibly the Fuser Heat Roll to keep it running.

012-xxx codes
Generally: Finisher problems

013-xxx codes
Generally: Finisher / Booklet Maker problems

016-xxx codes
Generally: Options or Software failures

016-311
Scanner not detected

024-340 thru 024-747
ESS (Network Controller) problems

024-910 thru 024-917
Paper size Sensing problems (in one of the paper drawers)

024-919
Face Up Tray interlock open

024-920/922
Face Down Tray 1 full / Face Down Tray 2 full

024-923/924/ 925
Toner Cartridge Empty - Y / M / C

024-927/930
OCT (Offset Catch Tray) full / Stacker Tray full

024-934 thru 024-939
Paper type mismatch errors

024-946/947/ 948/949
Tray not in position (T1/2/3/4)

024-950/951/ 952/953/954/ 955/956
No Paper in tray (T1/2/3/4/5/6/7)

042-313
Rear Fuser Cooling Fan failure

042-320/321/ 322/323
Drum Motor failures - 320=Y, 321=C, 322=M, 323=K (black)

042-324
IBT Belt Drive Motor failure

042-325
Main Motor failure

042-326
IBT Belt Home position not detected in time

042-327
IBT Belt Position failure

042-328
IBT Belt Edge Sensor failure

042-330
Fuser Exhaust Fan failure

042-331
Blower Motor Fan failure

042-600/601/ 602
Belt Edge timing failures

042-603
Suction Filter end of life

045-xxx codes
Printing communication failures

061-320/321
ROS (Laser Unit) polygon motor failures

061-323 thru 061-607
ROS (Laser Unit) problems

062-357
CCD (Scanner) Fan failure

062-360
Exposure Carriage position failure.

062-371
Exposure Lamp not lighting (or very dim)

071-101 thru 071-105
Paper Jams from Tray 1 at takeaway or registration

071-210
Tray 1 Lift failure

072-101 thru 072-105
Paper jams from Tray 2 at takeaway or registration

072-210
Tray 2 Lift failure

073-101 thru 073-105
Paper jam from Tray 3 at takeaway or registration

073-210
Tray 3 Lift failure

074-101 thru 074-105
Paper jam from Tray 4 at takeaway or registration

074-210
Tray 4 Lift failure

075-100 thru 075-135
Paper jam from Tray 5 at takeaway or registration

075-210/211
Tray 5 Lift failure / Lift down failure

077-103 thru 077-118
Fuser Exit Sensor jam or final Exit Sensor jam.

077-120
Post 2nd BTR Roll Sensor jam

077-123 thru 077-130
Inverter jams

077-300
Front Cover interlock open

077-301
Left Door interlock open

077-302
Right Cover interlock open

077-303
Transfer Module 2 interlock open

077-909
Paper detected in paper path at power-on

078-100 thru 078-151
Paper jam from Tray 6 / High Capacity Feeder (HCF) at takeaway or registration

078-250
Tray 6 (HCF) Lift failure

078-300
HCF (Hi Capacity Feeder) Top Cover interlock open

078-301
HCF Docking Interlock open

089-600 thru 089-617
Image Registration Control problems

091-311
BCR and Black Charge Corotron Cleaner control problem

091-312
Black Charge / Preclean HVPS (Hi Volt Power Supply) failure


091-313
Drum Cartridge CRUM (chip) communication failure

091-320
Black Charge Corona Wire is broken

091-400
Waste Toner Bottle replacement needed soon

091-401
Black Drum Cartridge near end of life

091-403
Black Charge Corotron Assembly near end of life

091-404
Black Charge Corotron Assembly has reached end of life

091-411
Yellow Drum Cartridge near end of life

091-421
Magenta Drum Cartridge near end of life

091-431
Cyan Drum Cartridge near end of life

091-910
Waste Toner Bottle not detected

091-911
Waste Toner Bottle full

091-913
Black Drum Cartridge at end of life

091-914 thru 091-916 or 091-921
Black Drum Cartridge CRUM communication problems

091-917/920/924/925/927
Yellow Drum Cartridge CRUM communication problems

091-918/922/ 928
Magenta Drum Cartridge CRUM communication problems

091-919/923/ 926/929
Cyan Drum Cartridge CRUM communication problems

091-932
Yellow Drum Cartridge end of life

091-933
Magenta Drum Cartridge end of life

091-934
Cyan Drum Cartridge end of life

092-649/650
ADC Sensor Shutter failures

092-651/652
IBT Belt ADC Sensor (MOB ADC) failures

092-653 thru 092-660
ATC (from Developer Unit) problems…653/657=yellow, 654/658=magenta, 655/659=cyan, 656/660=black

093-300
Marking Drawer Interlock open

093-313 thru 093-317
Toner Dispense problems… 314=Y, 315=M, 316=C, 317=K (black)

093-320
Developer Motor failure

093-421 thru 093-425
Toner Cartridges low 421/422=K(black), 423=Y, 424=M, 425=C

093-600 thru 093-912
Toner Dispense problems (600=Y, 601=M, 602=C, 603/912=K(Black),

093-918 thru
Toner CRUM failures (918/924 /925/926/936/ 940=K(black),927/933/937 =Y, 928/934/938 = M , 929/935/939=C

093-940

094-320/321
1st BTR (Transfer Roll) retract or contact problems

094-322/323
2nd BTR (Transfer Roll) retract or contact problems

102-xxx codes
Generally: Network Controller (ESS) problems

112-700
Finisher Punch Dust Box full (hole punch bin)

116-xxx codes
Generally: Network Controller (ESS) problems

123-xxx codes
Generally: UI (control panel) faults

124-xxx codes
Generally: Configuration errors (e.g., serial number disagreement between various boards or machine speed errors, etc)

127-xxx codes
Printing failures



42 comments:

  1. 010-326 error occur while printing,please help how to fix this error and why this error occur suddenly

    ReplyDelete
  2. 091-910 error. Waste container is in machine, but not being recognized. Blown fuse maybe?

    ReplyDelete
  3. 015-387 pl give comment on this error code( 2240 machine model)

    ReplyDelete
  4. 077-120 error came in mu machine i.e fuji xerox docucentre-III c5500
    what is the solution of this?

    ReplyDelete
  5. 010-321 error cor
    what is the sollution on this

    ReplyDelete
  6. 010-321 error code in xerox dc 240
    what is the sollution on this?

    ReplyDelete
  7. Xerox Dc 240 error code 091-320 solution

    ReplyDelete
  8. Please help Xerox 252 Error code 024-934 paper type mismatch
    if i send a print from bypass the paper paper goes in and then just slips inside and shows error 024-934 print driver mismatch
    if you any idea please help

    ReplyDelete
  9. I have a Xerox WC7232 that is saying the front door is open and has an error code 077-300 witch is the front door interlock switch. Should that be replaced or is there another cause for this because its also saying that one of the cartridges or consumables is not seated properly. And the drum is no good. Could replacing the drum unit solve this whole problem?

    ReplyDelete
  10. Please solve my problem is 252 error code 003-341 please solve

    ReplyDelete
  11. Please solve my problem
    There is error code 063-355 in docucolour 252

    ReplyDelete
  12. DC 240 error code 101 - 321 ?? please assist

    ReplyDelete
  13. DC 240 error code 101-321 ??

    ReplyDelete
  14. DC 252 error code 093 320 how to riper. ?

    ReplyDelete
  15. DC 252 error code 093 320 how to riper. ?

    ReplyDelete
  16. halou help meee whats this code 121-333 i search in internet and i dont found nothing i by the maschine today anda came with this error........

    ReplyDelete
  17. halou help meee whats this code 121-333 i search in internet and i dont found nothing i by the maschine today anda came with this error........

    ReplyDelete
  18. Dear Sir Xerox Work Center DC 250 Error Code 045-310

    ReplyDelete
  19. 042-325 Error code need help please!!!

    ReplyDelete
  20. Erro 42.427 Dc250 o que pode ser

    ReplyDelete
  21. please code 091-312
    Black Charge / Preclean HVPS (Hi Volt Power Supply) failure, help!!! what is solution?

    ReplyDelete
  22. I have a Xerox d95, error code 077-330. Can't find that code anywhere for the love of God. Please help!

    ReplyDelete
  23. 024-370 errcode pls give soluction

    ReplyDelete
  24. Plz send nvm value for center the print position in xerox 252

    ReplyDelete
  25. Please help for error code 124-374 of my Xerox DC-250.

    ReplyDelete
  26. My dc250 showing 124-374 error code. I have clean and re install ess board but still it showing above code after some time tuning on the machine. Please help.

    ReplyDelete
    Replies
    1. This is serial number mismatch error of ess board and msi board. Both are same in default position.

      Delete
  27. My xerox DC250. Please help for error code 124-374.

    ReplyDelete
  28. how to solve error code 061-341

    ReplyDelete
  29. xerox 252 fiery need me my what app no is 7017494132

    ReplyDelete
  30. Replies
    1. Please check your file. This is file format error. If possible change file format

      Delete
  31. how to reset fuser code 010-421

    ReplyDelete
  32. My Xerox is 252. Please what to do with error code 620-357?

    ReplyDelete